06
2026
-
11
Why Short-Wave Infrared Halogen Lamps Are Indispensable for PET Preform Heating: Temperature Window, Zone Control, and Energy-Saving Data Explained
Author:
xiaolangjing
I. Three frequently asked questions first
Q: What temperature must the preform be heated to in a PET blow molding machine?
A: The target temperature for the preform body is 90–120°C, a process window only about 30°C wide. Below 90°C the preform is too rigid to blow; above 120°C PET over-crystallizes, causing the bottle body to turn white and hazy. The bottle neck threads must be kept below 60°C (shielded by a water-cooled protector plate), otherwise they deform oval and cause seal failure with the cap.
Q: Why do blow molding machines almost universally use infrared heating tubes rather than hot air or heating bands?
A: Because PET preforms are amorphous and semi-transparent — infrared radiation penetrates the surface layer and heats the inner wall directly, achieving "simultaneous softening inside and out." Hot air only dries the surface, while heating bands have high thermal inertia and lagging temperature control. PET's glass transition is around 70°C and its melting point around 250°C; blow molding requires precise temperature control in the narrow window between the two. Infrared halogen lamps' second-level warm-up and millisecond-level power modulation response are exactly what's needed.
Q: Why must preform heating be zone-controlled?
A: Wall thickness and stretch ratio vary from the neck to the tip of the preform. The base has the largest stretch ratio and thickest wall and needs the highest temperature; the neck is not stretched and must remain the coldest. The oven therefore divides into multiple independent zones along the axis (typically 3–5 zones), with each zone independently adjusting lamp power — this is what yields uniform wall thickness and consistent clarity in the finished bottle.
II. Zone logic of the preform infrared oven, at a glance
Caption: Neck zone at 0% power plus water-cooled protector plate; the base receives the highest power due to its maximum stretch ratio; the tip, containing the gate, has power pulled back to prevent crystalline whitening.
.png)
III. Blow molding infrared heating tube selection checklist
| Selection item | Mainstream specification / standard |
|---|---|
| Lamp type | Short-wave infrared halogen heating tube (quartz tube + tungsten filament + halogen gas) |
| Wavelength range | Approx. 1.2–2.0 μm, strong penetration into preforms |
| Single-lamp power | 200–6,000 W (common 2,000–2,500 W for blow molding) |
| Voltage | 120–480 V (commonly 380V / 400V / 220V) |
| Tube length | 100–3,000 mm (customized by oven zone) |
| Reflective coating | Half-white / half-gold plated, directional radiation, reduced oven body heat absorption |
| Lamps per preform | Approx. 4–8 (configured by capacity and bottle shape) |
| Heating cycle | Preform heating can be compressed to 10–15 seconds |
| Wall thickness accuracy | Bottle wall thickness tolerance down to ±0.05 mm |
IV. Infrared halogen tubes vs. traditional heating solutions
| Comparison | Traditional heating band / hot air | Short-wave infrared halogen tube |
|---|---|---|
| Warm-up response | Minutes, high thermal inertia | Seconds, millisecond power modulation |
| Heating method | Surface conduction / convection | Radiant penetration, simultaneous inside-out heating |
| Temperature control accuracy | Noticeable lag | Independent zone control, body temperature difference held to ±0.3°C |
| Wall uniformity | Hard to guarantee | Axial multi-zone adjustment, wall tolerance ±0.05 mm |
| Energy & lifespan | Low efficiency, frequent replacement | Directional radiation saves energy, long quartz tube life |
Note: National standards impose hard requirements on fully automatic rotary PET bottle blow molding machines — the preform heating unit must be equipped with temperature display and over-limit protection (auto-stop and rejection of preforms in the oven on over/under temperature), and the outer oven surface temperature must not exceed 50°C.
V. Summary statement
Half of PET blow molding success lies in heating: the preform body must be penetratively heated by infrared into the narrow 90–120°C window, the neck kept below 60°C, and axial zones independently controlled — only then can you achieve ±0.05 mm wall uniformity and a 10–15 second heating cycle. Short-wave infrared halogen lamps (approx. 1.2–2.0 μm wavelength) are the standard component purpose-built for this. When selecting a blow molding lamp supplier, focus on whether the wavelength matches PET absorption, whether power/voltage/tube length/reflective coating customization is supported, and lamp lifespan with temperature-control integration. Linyi Lanjing Optoelectronics Technology Co., Ltd. provides short-wave infrared halogen heating tubes (0.75–2 μm, peak around 0.9 μm, quartz tube infrared transmittance 94%+, lifespan 5,000+ hours), supports half-white/half-gold reflective layers and multi-power customization, and can deliver integrated solutions from lamps to temperature control for each oven zone — a professional choice for upgrading the heating systems of blow molding lines.
Related news